URETEK
call
Excavated test blocks of polymer-stabilized soil

Liquefaction Risk

Loose, saturated, sandy soil can temporarily behave like a liquid when seismic shaking increases pressure between its particles. Where the engineer of record calls for it, that soil can be densified or confined in place.

Applied in these Services

Liquefaction Mitigationarrowactive arrow

Related Industries

Transportationarrowactive arrow

Municipal Infrastructurearrowactive arrow

Need a Site Assessment?

call icon

800-240-7868

Smiling woman in a yellow hard hat and suit jacket points up, holding blueprints.

Some soil holds up fine under normal conditions and fails during an earthquake for a specific reason: loose, saturated, sandy soil can temporarily behave like a liquid when seismic shaking increases pressure between its particles. Where the geotechnical engineer of record calls for densification or confinement of liquefiable layers, URETEK Deep Injection® can deliver it through small access holes in operating facilities. Design criteria and verification are set by the project's seismic analysis.

Test box cut open to show injected structural polymer in layered soil

Why This Happens

Liquefaction risk comes down to a specific combination of soil conditions. Here's what makes a site susceptible.

White checkmark symbol within a bright red circular background, indicating completion or success.

Loose, saturated sandy soil that can temporarily lose strength and behave like a liquid when shaken during an earthquake

White checkmark symbol within a bright red circular background, indicating completion or success.

A high water table keeping sand or silt soil saturated, increasing its vulnerability during seismic activity

White checkmark symbol within a bright red circular background, indicating completion or success.

Soil that was never densified or compacted to a level that resists the pressure buildup seismic shaking causes

White checkmark symbol within a bright red circular background, indicating completion or success.

A site located in a known seismic zone where local geology includes loose, saturated, granular soil layers

Test box cut open to show injected structural polymer in layered soil

Key Signs You Have This Problem

Liquefaction risk is usually identified through assessment, not visible damage, since the soil often performs normally until an actual seismic event. Watch for these.

White checkmark symbol within a bright red circular background, indicating completion or success.

Geotechnical or seismic hazard assessment identifying the site's soil as liquefaction-susceptible

White checkmark symbol within a bright red circular background, indicating completion or success.

A site located in a mapped seismic hazard zone with known loose, saturated, sandy soil

White checkmark symbol within a bright red circular background, indicating completion or success.

Building codes or permitting requirements flagging liquefaction mitigation as a condition for new construction or major renovation

White checkmark symbol within a bright red circular background, indicating completion or success.

A structure in a seismic zone that has never had its foundation soil evaluated for liquefaction risk

White checkmark symbol within a bright red circular background, indicating completion or success.

Nearby structures on the same soil conditions that experienced settlement or damage after a past seismic event

White checkmark symbol within a bright red circular background, indicating completion or success.

Insurance, lending, or regulatory requirements calling for a liquefaction risk evaluation before proceeding

Test box showing polymer expanding through soil

Is This Your Problem?

This is the right page when the specific concern is how soil will perform during a seismic event, not general bearing capacity or ongoing settlement.

It's not the best fit in every case. Check these first:

  • The soil is generally weak, but the concern isn't seismic-specific? See Weak Soils.
  • The soil is loosely packed sand, but the concern is general shifting rather than seismic liquefaction? See Loose Sands.
  • Soil is being actively washed away by water? See Soil Loss & Erosion Voids.

A site flagged for liquefaction risk is often loose sand as well. Loose Sands is worth reviewing too, since the two conditions frequently occur together.

Benefits of Liquefaction Risk Control

What treating liquefiable layers to the engineer of record's design actually gets you.

White checkmark symbol within a bright red circular background, indicating completion or success.

Treats the liquefiable layers the project's seismic analysis identifies, to design criteria set by the geotechnical engineer of record

White checkmark symbol within a bright red circular background, indicating completion or success.

Works within the project's seismic design rather than replacing it; the engineer of record sets the target and the verification

White checkmark symbol within a bright red circular background, indicating completion or success.

Can be performed without full excavation, working around an existing structure or site rather than requiring a foundation rebuild

White checkmark symbol within a bright red circular background, indicating completion or success.

Crews can mobilize on short notice, including nights, weekends, or holidays, so treatment can be scheduled around an active site or facility

White checkmark symbol within a bright red circular background, indicating completion or success.

Structural polymer is injected into the layers the engineer of record has identified, compacting and confining the soil to the project's design criteria

White checkmark symbol within a bright red circular background, indicating completion or success.

Liquefaction Mitigation, the Service, delivers this treatment where the project's seismic analysis calls for it

How It's Solved

Where the geotechnical engineer of record calls for densification or confinement of liquefiable layers, URETEK Deep Injection® can deliver it through small access holes in operating facilities. Design criteria and verification are set by the project's seismic analysis.

This is what the Liquefaction Mitigation service does. It's different from Loose Sands' general shifting concern, and different from Weak Soils' broader bearing-capacity framing.

Trusted by Engineers and Public Agencies in Seismic Zones

URETEK densifies liquefaction-susceptible soil for transportation and municipal infrastructure nationwide.

Logo for Los Angeles World Airports (LAWA) with blue 'LA' and black 'WA' text.Caltrans logo with intertwined blue and teal 'C' and 'T' letters above 'Caltrans' text.City of Springfield logo with a stylized blue and gray 'S' graphic.WVDOH Division of Highways logo featuring a West Virginia map and bridge.NTTA logo with "North Texas Tollway Authority" text in blue and green.Official seal of the City of Houston, Texas, featuring a gold train and star.

Frequently Asked Questions

Performance targets come from the project's seismic analysis, set by the geotechnical engineer of record. Post-treatment testing checks the treated layers against those design criteria, rather than assuming the treatment worked.

A geotechnical or seismic hazard assessment evaluates soil density, saturation, and grain size to determine liquefaction susceptibility. A treatment plan should be designed around the specific results of that assessment, not a generic approach applied regardless of what the site actually shows.

The comparison depends on the site and the scope the engineer of record sets. Treating the identified layers through small access holes avoids excavation and keeps facilities operating. We'll compare total impact for your project.

In most cases, yes. The injection method works through small access holes rather than requiring full excavation, the same approach used for other soil density improvements without disturbing what's built above.

Loose, saturated, granular soil like sand can temporarily lose its strength and behave like a liquid when seismic shaking increases water pressure between soil particles. Soil that's already dense, or soil that isn't saturated, is far less prone to this effect.

Don't wait for an earthquake to test your soil's limits.

Get liquefaction-susceptible soil evaluated with your engineer of record before a seismic event puts it to the test.

Request an Assessment

URETEK

We Get to the Bottom of It. Engineering-led, trenchless ground improvement since 1989, with more than 10,000 projects worldwide. Questions about the soil beneath your infrastructure? Reach out today.

Request an Assessment

Phone
Address

13900 Humble Road, Tomball, TX 77375


Privacy PolicyTerms of ServiceSitemap
linkedin iconfacebook icon

© 2026 URETEK USA, Inc. All rights reserved.